Call us at 732 292-1994 or 800 867-6690   |  Email us at triadscientific@gmail.com  |  Visite us on

facebook

TAC-60L/60i

Thermal Analysis >> TAC-60L/60i

TAC-60L/60i
Automatic Cooling Attachments

The DSC-60/60A (Differential Scanning Calorimeter) can use the "liquid nitrogen cooling type TAC-60L" or "electric cooling type TAC-60i" as attachments for low-temperature (cooled) measurement".

Low-Temperature (Cooled) Measurement

Thermal analysis measurement at low temperatures is widely used for evaluating physical characteristics of oils/fats in foods/cosmetics, various oils, waxes, rubbers, and plastics (for example, measuring the transition point at low temperatures).

The figure on the right (upper) shows a measurement example where two types of automobile engine oil are cooled to -120 °C and then heated. It can be seen that sample M has better cold resistance since it coagulates at lower temperatures. (TAC-60L used)

Reference) Thermal Analysis Application News No.T139

The figure on the right (lower) shows data obtained by measuring commercially-available lipsticks (A, B, C). The peaks are caused by melting of wax and oil/fat in the lipstick. Peak shapes differ greatly according to type of lipstick.

TAC-60L Liquid Nitrogen Cooling System

DSC-60A + TAC-60L + TA-60WS PC set + FC-60A + ATG-60, etc.

DSC-60A + TAC-60L + TA-60WS PC set + FC-60A + ATG-60, etc.

The TAC-60L system uses liquid nitrogen as the catalyst for cooling samples down to -130 °C.

  • Stable Baseline

  • The tank internal pressure is optimally controlled according the residual amount of liquid nitrogen in the tank to keep the supply flowrate constant. Pulsation is reduced, and the DSC baseline is stable even during cooling.
  • Space-Saving

  • Installation space is saved since the liquid nitrogen supply control system is placed compactly in the pump head section.
  • Refrigerant Savings

  • Samples can be cooled only when required since supply start/stop is controlled in steps according to a temperature program. Also, for safe operation and minimizing refrigerant consumption, refrigerant supply is automatically stopped when the measuring unit reaches a high temperature.
  • Autosampler Continuous Measurement Supported

  • Samples can be replaced easily during cooling thanks to the unique layout at the rear of the cooling unit. Moreover, gas can be allowed to pass for a fixed period of time after measurement ends to prevent dew and frost condensation. (when the optional ATG-60 is connected)

* Including accessory liquid nitrogen tank (35 L). The continuous operating time when this tank is used is approximately 8 hours. (This changes according to the temperature program.)

TAC-60i Electric-Cooling Attachment

DSC-60A + TAC-60i + TA-60WS PC set + FC-40A + cooling unit

DSC-60A + TAC-60i + TA-60WS PC set + FC-40A + cooling unit

The TAC-60i electric-cooling type attachment does not require liquid nitrogen, and can cool samples to down -50 °C.

  • No Catalyst Required

  • Liquid nitrogen or other catalysts are not used, which means that liquid nitrogen need not be prepared before measurement or that there is no worry about ventilation.
  • Just Connect the Cooling Unit

  • Samples can be cooled down to -50 °C for measurement by simply connecting a commercially-available cooling unit (intra cooler).

Selection Between TAC-60L Liquid Nitrogen Cooling System and TAC-60i Electric-Cooling Attachment

TAC-60L: This is recommended when cooling down to -50 Ã‚°C or less (possible down to -130 Ã‚°C) or when mixing cooled and non-cooled measurements.
TAC-60i: This is recommended when it is difficult to obtain liquid nitrogen on a daily basis, when it is difficult to ventilate vaporized nitrogen from the test room, and when performing measurement for 8 hours or more non-stop.

DSC-60 Plus Series

DSC-60 Plus Series

DTA-50

DTA-50

DTG-60/DTG-60A

DTG-60/DTG-60A

TA-60WS

TA-60WS

TAC-60L/60i

TAC-60L/60i

TGA-50/50H And TGA-51/51H

TGA-50/50H And TGA-51/51H

TMA-60/60H

TMA-60/60H

WHY YOU SHOULD CHOOSE TO DO BUSINESS WITH TRIAD SCIENTIFIC

1. EXPERIENCED-We have been building labs, equipping labs, and supplying lab equipment parts and service for over 20 years. With over 100 years of combined lab equipment experience at our site and working with many experienced technicians, we try to offer the right equipment at the right price for you, our partner.

2. SAVE MONEY- We sell, lease, and rent - You save money, 5-70% off original retail, so you get great equipment at a great price.

3. WARRANTY -We offer a warranty on our refurbished equipment and new manufacturer warranty on new equipment.

4. SERVICE- We offer instrument service, refurbishment validations, and calibrations at great rates and skill levels.

5. INSTRUMENT PARTS- We sell new instrument parts and new equipment parts and hard to find used older parts

6. UNIQUE- We are an independent dealer and also sell used instruments, such as AA, FTIR, GC, GC/MS, HPLC, LC/MS, ICP, ICP/MS, Particle Size Analysis, UV/VIS, and UV/VIS/NIR. This equipment is manufactured by companies like Agilent, Hewlett Packard, Waters, Hitachi, Perkin Elmer, Shimadzu, Beckman, and more. WE ARE NOT AFFILIATED WITH THESE COMPANIES IN ANY WAY!

7. BUILD LABS- We well discounted made in USA Lab Casework, Fume hoods, Blowers, Safety Cabinets, and Clean Benches.

8. CASH PAID-Top dollar paid, and you can sell your excess, obsolete, surplus equipment with us. We can buy it or sell on consignment.

9. DIVERSIFIED-We sell a very broad line of new and used Lab Equipment. See our detailed listing above.

CLICHERto join TRIAD SCIENTIFIC'S NEW MAILING LIST and GET SPECIAL LIMITED TIME OFFERS !!!